View BTS441T08_4926998.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Smart Power High-Side-Switch One Channel: 20 m
BTS441T
Product Summary
On-state Resistance Operating Voltage Nominal load current Current limitation RON Vbb(on) IL(ISO) IL(lim) 20m 4.75 ... 41V 21A 65A
Package
TO-220-5-11 TO-263-5-2 TO-220-5-12
Standard
SMD
Straight
*HQHUDO 'HVFULSWLRQ
* * N channel vertical power FET with charge pump, ground referenced CMOS compatible input, monolithically integrated in Smart SIPMOS technology. * Green Product (RoHS compliant) Providing embedded protective functions. * AEC Qualified
$SSOLFDWLRQ
* * * *
C compatible power switch for 5V, 12 V and 24 V DC applications All types of resistive, inductive and capacitve loads Most suitable for loads with high inrush currents, so as lamps Replaces electromechanical relays, fuses and discrete circuits
* * * * *
%DVLF )XQNWLRQV
Very low standby current Optimized static electromagnetic compatibility (EMC) C and CMOS compatible Fast demagnetization of inductive loads Stable behaviour at undervoltage
3URWHFWLRQ )XQFWLRQV
* * * * * * * * Short circuit protection Current limitation Overload protection Thermal shutdown Overvoltage protection (including load dump) with external GND-resistor Reverse battery protection with external GND-resistor Loss of ground and loss of Vbb protection Electrostatic discharge (ESD) protection
9EE
,1
/RJLF ZLWK SURWHFWLRQ IXQFWLRQV
287 /RDG
352)(7 *1'
Data sheet
1
Rev. 1.11, 2008-12-09
BTS441T
)XQFWLRQDO GLDJUDP
RYHUYROWDJH SURWHFWLRQ LQWHUQDO YROWDJH VXSSO\ ORJLF
JDWH FRQWURO FKDUJH SXPS WHPSHUDWXUH VHQVRU
FXUUHQW OLPLW
9%%
FODPS IRU LQGXFWLYH ORDG 287
,1
(6'
/2$'
*1'
PROFET
3LQ 'HILQLWLRQV DQG )XQFWLRQV 3LQ 7DE 6\PERO *1' ,1 9EE 1& 287 9EE )XQFWLRQ /RJLF JURXQG ,QSXW DFWLYDWHV WKH SRZHU VZLWFK LQ FDVH RI ORJLFDO KLJK VLJQDO 3RVLWLYH SRZHU VXSSO\ YROWDJH 7KH WDE LV VKRUWHG WR SLQ 1RW FRQQHFWHG 2XWSXW WR WKH ORDG 3RVLWLYH SRZHU VXSSO\ YROWDJH 7KH WDE LV VKRUWHG WR SLQ
3LQ FRQILJXUDWLRQ WRS YLHZ
7DE
9%%

*1' ,1
1& 287
Data sheet
2
Rev. 1.11, 2008-12-09
BTS441T
Maximum Ratings at Tj = 25 C unless otherwise specified Parameter Supply voltage (overvoltage protection see page 4) Supply voltage for full short circuit protection Tj Start=-40 ...+150C Load dump protection1) VLoadDump = VA + Vs, VA = 13.5 V RI2)= 2 , RL= 0,5 , td= 200 ms, IN= low or high Load current (Short-circuit current, see page 5) Operating temperature range Storage temperature range Power dissipation (DC) ; TC25C Maximal switchable inductance, single pulse Vbb = 12V, Tj,start = 150C, TC = 150C const. (see diagram, p.8) IL(ISO) = 21 A, RL= 0 : E4)AS=0.7J: Electrostatic discharge capability (ESD) IN: (Human Body Model) Out to all other pins shorted:
acc. MIL-STD883D, method 3015.7 and ESD assn. std. S5.1-1993; R=1.5k; C=100pF
Symbol Vbb Vbb
Values 43 34 60 self-limited -40 ...+150 -55 ...+150 125 2.1 1.0 8.0 -10 ... +16 2.0 1 75 33
Unit V V V A C W mH kV
VLoad dump3) IL Tj Tstg Ptot
ZL VESD
Input voltage (DC) Current through input pin (DC)
see internal circuit diagrams page 7
VIN IIN RthJC RthJA
V mA K/W
Thermal resistance
chip - case: junction - ambient (free air): SMD version, device on pcb5):
1) 2) 3) 4) 5)
Supply voltages higher than Vbb(AZ) require an external current limit for the GND pin, e.g. with a 150 resistor in the GND connection. A resistor for the protection of the input is integrated. RI = internal resistance of the load dump test pulse generator VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 EAS is the maximum inductive switch off energy Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70m thick) copper area for Vbb connection. PCB is vertical without blown air.
Data sheet
3
Rev. 1.11, 2008-12-09
BTS441T
Electrical Characteristics
Parameter and Conditions
at Tj =-40...+150C, Vbb = 12 V unless otherwise specified
Symbol
Values min typ max
Unit
Load Switching Capabilities and Characteristics On-state resistance (Vbb (pin3) to OUT (pin5)); IL = 2 A Vbb7V: Tj=25 C: RON Tj=150 C:
see diagram page 9
--
15 28 21 -90 110 ---
20 37 -2 200 250 1 1
m
Nominal load current (pin 3 to 5) `ISO 10483-1, 6.7:VON=0.5V, TC=85C Output current (pin 5) while GND disconnected or GND pulled up6), Vbb=30 V, VIN= 0,
see diagram page 7
IL(ISO) IL(GNDhigh)
17 -40 40 0.1 0.1
A mA s V/s V/s
Turn-on time IN Turn-off time IN RL = 12 , Slew rate on 10 to 30% VOUT, RL = 12 , Slew rate off 70 to 40% VOUT, RL = 12 ,
to 90% VOUT: ton to 10% VOUT: toff dV /dton -dV/dtoff
Operating Parameters Operating voltage
Tj =-40C Vbb(on) Tj =+25C Tj =+105C6) Tj =+150C Overvoltage protection7) Tj =-40C: Vbb(AZ) I bb = 40 mA Tj =+25...+150C: Standby current (pin 3) 8) Tj=-40...+25C: Ibb(off) Tj=+105C6): VIN=0 see diagram page 9 Tj=+150C: IL(off) Off-State output current (included in Ibb(off)) VIN=0 Operating current (Pin 1)9), VIN=5 V, IGND
4.75 4.75 4.75 5.0 41 43 ------
-----47 5 --1.5 2
41 43 43 43 -52 10 10 25 10 4
V
V A A mA
6) 7) 8) 9)
not subject to production test, specified by design see also VON(CL) in table of protection functions and circuit diagram page 7 Measured with load, typ. 40 A without load. Add IIN, if VIN>5.5 V
Data sheet
4
Rev. 1.11, 2008-12-09
BTS441T
Parameter and Conditions
at Tj =-40...+150C, Vbb = 12 V unless otherwise specified
Symbol min
Values typ max
Unit
Protection Functions10) Current limit (pin 3 to 5)
(see timing diagrams, page 9)
IL(lim) Tj =-40C: Tj =25C: Tj =+150C: IL(SCr) Tj,start =25C: Toff(SC)
--40 --41 43 150 ----65 -55 14 -47 -10 -540 85 -----52 --32 -A A ms V C K V mV
Repetitive short circuit current limit Tj = Tjt (see timing diagrams, page 10) Thermal shutdown time11)12)
(see timing diagram on page 10)
Output clamp (inductive load switch off)
at VOUT = Vbb - VON(CL), IL= 40 mA
;Tj =-40C: Tj=25..150C: VON(CL) Thermal overload trip temperature Tjt Thermal hysteresis Tjt Reverse battery (pin 3 to 1) 13) -Vbb Reverse battery voltage drop (VOUT > Vbb) -VON(rev) IL = -2A Tj =+150C:
10)
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not designed for continuous repetitive operation. 11) not subject to production test, specified by design 12) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70m thick) copper area for V bb connection. PCB is vertical without blown air. 13) Requires 150 resistor in GND connection. The reverse load current through the intrinsic drain-source diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature protection is not active during reverse current operation! Input and Status currents have to be limited (see max. ratings page 1 and circuit page 7).
Data sheet
5
Rev. 1.11, 2008-12-09
BTS441T
Parameter and Conditions
at Tj =-40...+150C, Vbb = 12 V unless otherwise specified
Symbol
Values min typ max
Unit
Input14) Input resistance Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state input current (pin 2) On state input current (pin 2)
see circuit page 7
RI VIN(T+) VIN(T-) VIN(T) VIN = 0.4 V: IIN(off) VIN = 5 V: IIN(on)
2.5 1.2 0.8 -1 4.5
3.8 --0.3 -12
6.5 2.2 --15 24
k V V V A A
14)
If a ground resistor RGND is used, add the voltage drop across this resistor.
Data sheet
6
Rev. 1.11, 2008-12-09
BTS441T
Terms
9 ,EE EE , ,1 9 ,1 ,1 /HDGIUDPH 9EE 352)(7 *1' 5 *1' 287 ,/ 921
Overvolt. and reverse batt. protection
9EE 9
=
5 ,1
,1
5, /RJLF
287 9 =
352)(7
*1'
,*1'
9287
5 *1'
6LJQDO *1'
5 /RDG
/RDG *1'
Input circuit (ESD protection)
,1 5 ,
VZ1 = 6.1 V typ., VZ2 = 47 V typ., RGND = 150 , RI= 3.5 k typ. In case of reverse battery the load current has to be limited by the load. Temperature protection is not active
(6'=' , *1'
GND disconnect
, ,
The use of ESD zener diodes as voltage clamp at DC conditions is not recommended.
9EE ,1 352)(7 *1' 9 EE 9 ,1 9 *1' 287
Inductive and overvoltage output clamp
9 EE 9 =
9
21
Any kind of load. In case of Input=high is VOUT VIN - VIN(T+) .
287 *1'
352)(7
GND disconnect with GND pull up
VON clamped to 47 V typ.
9EE ,1 352)(7 287
*1'
9
9 EE
,1
9
*1'
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Data sheet
7
Rev. 1.11, 2008-12-09
BTS441T
Vbb disconnect with charged inductive load
Inductive load switch-off energy dissipation
( EE ( $6 9EE ,1 352)(7 *1' 287 (/RDG
9EE KLJK ,1 352)(7 287
*1'
9
EE
=/
^
/
(/
For inductive load currents up to the limits defined by ZL (max. ratings and diagram on page 8) each switch is protected against loss of Vbb. Consider at your PCB layout that in the case of Vbb disconnection with energized inductive load all the load current flows through the GND connection.
5 /
(5
Energy stored in load inductance:
EL = 1/2*L*I L
While demagnetizing load inductance, the energy dissipated in PROFET is
2
EAS= Ebb + EL - ER= VON(CL)*iL(t) dt,
with an approximate solution for RL > 0 : IL* L (V + |VOUT(CL)|) 2*RL bb IL*RL
EAS=
OQ (1+ |V
OUT(CL)|
)
Maximum allowable load inductance for a single switch off
/ I ,/ Tj,start = 150C, Vbb = 12 V, RL = 0
L [mH]

IL [A]
Data sheet
8
Rev. 1.11, 2008-12-09
BTS441T
Typ. on-state resistance
521 I 9EE7M ; IL = 2 A, IN = high RON [m]

Vbb [V]
7M
&
& &
Typ. standby current
,EERII I 7M ; Vbb = 9...34 V, IN1,2 = low Ibb(off) [A]

Tj [C]
Data sheet
9
Rev. 1.11, 2008-12-09
BTS441T
Timing diagrams
Figure 1a: Vbb turn on:
,1
Figure 2b: Switching a lamp,
,1
9
287
9 EE
,
/
9
W
287
Figure 3a: Short circuit shut down by overtemperature, reset by cooling
proper turn on under all conditions
,1
RWKHU FKDQQHO QRUPDO RSHUDWLRQ
Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition:
,
/
,1
,
/OLP , /6&U
9287
W on G9GWRQ W G9GWRII
W
RII6&
W
Heating up may require several milliseconds, depending on external conditions
off
Figure 4a: Overtemperature: Reset if Tj ,1
,/
9
287
W
7
-
W
Data sheet
10
Rev. 1.11, 2008-12-09
BTS441T
Package Outlines
10 0.2 9.9 0.2 8.5 1) 3.7 -0.15
A 4.4 1.27 0.1
15.65 0.3
17 0.3
2.8 0.2
12.95
0...0.3
1)
9.25 0.2
8.6 0.3
10.2 0.3
3.7 0.3
C 0.5 0.1 3.9 0.4
0...0.15 5 x 0.8 0.1 4 x 1.7
1)
0.25
M
AC
8.4 0.4
Typical All metal surfaces tin plated, except area of cut.
figure 5: PG-TO220-5-11 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data sheet 11
Rev. 1.11, 2008-12-09
1.6 0.3
Dimensions in mm
0.05 2.4
BTS441T
10 0.2 9.9 0.2 8.5 1) 3.7 -0.15
A B 4.4 1.27 0.1
15.65 0.3
17 0.3
2.8 0.2
12.95
0...0.3
1)
11 0.5
C 0...0.15
13 0.5
0.5 0.1 5 x 0.8 0.1 2.4
M
4 x 1.7
1)
0.25
ABC
Typical Metal surface min. X = 7.25, Y = 12.3 All metal surfaces tin plated, except area of cut.
Figure 6: PG-TO220-5-12 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data sheet 12
9.25 0.2
Dimensions in mm Rev. 1.11, 2008-12-09
0.05 2.4
BTS441T
4.4 10 0.2 0...0.3
1 0.3
1.27 0.1 A B 0.05
7.55 1) 1.3 0.3
8.5 1)
(15)
9.25 0.2
2.4 0.1
4.7 0.5 2.7 0.3
0...0.15 5 x 0.8 0.1 4 x 1.7 0.25
M
0.5 0.1
AB
8 MAX.
0.1 B
1) Typical Metal surface min. X = 7.25, Y = 6.9 All metal surfaces tin plated, except area of cut.
Figure 7: PG-TO263-5-2 Green Product (RoHS compliant)
GPT09062
To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data sheet 13
Dimensions in mm Rev. 1.11, 2008-12-09
BTS441T
Revision History
Revision 1.11 Date 2008-12-09 Changes RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441T All pages: Infineon logo updated Page 1: Added "AEC qualified" and "RoHS" logo, added "Green Product (RoHS compliant)" and "AEC qualified" statement to feature list, package names changed to RoHS compliant versions, updated package drawing. Page 10-12: Package names changed to RoHS compliant versions ( PG-TO220-5-11, PGTO220-12 and PG-TO263-5-2), added "Green Product" description added Revision History added Legal Disclaimer
Data sheet
14
Rev. 1.11, 2008-12-09
Edition 2008-12-09 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2008 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

▲Up To Search▲

Price & Availability of BTS441T08

	To Download BTS441T08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .